IPv6: Differences between IPv4 and IPv6
The following table summarizes the major differences between IPv4 and IPv6:
mystudyblog
- Home
- CCNA Study
- What is a network?
- OSI -TCP IP models
- Encapsulation
- Ethernet frame
- MAC & IP addresses
- Unicast, multicast, and broadcast addresses
- Network devices
- Half duplex and full duplex
- IEEE Ethernet standards
- Cisco three-layer hierarchical model
- Cabling:Types of Ethernet cabling
- Cabling: Types of Ethernet cables
- Types of networks: Wide area network
- Types of networks: Local area network & Metropolitan area network
- IP addressing: Types of IP addresses
- IP addressing: Classes of IP addresses
- IP addressing: Subnetting explained
- IP addressing: Subnet mask
- IP addressing: Create subnets
- Network tools: Ping
- Network tools: Traceroute
- Network protocols: TCP-IP suite of protocols
- Network protocols: TCP explained
- Network protocols: UDP explained
- Network protocols: Ports explained
- Network protocols: ARP
- Network protocols: DHCP & DNS
- Network protocols: Telnet & SSH
- Network protocols: FTP & TFTP
- Network protocols: SNMP (Simple Network Management Protocol)
- Network protocols: HTTP & HTTPS
- Network protocols: NTP (Network Time Protocol)
- Network protocols: APIPA (Automatic Private IP Addressing)
- Network protocols: ICMP (Internet Control Message Protocol)
- Network protocols: IP header
- Cisco IOS: Cisco IOS overview
- Cisco IOS: Power on a Cisco device
- Cisco IOS: IOS command modes
- Cisco IOS: Get help in IOS
- Cisco IOS: Running & startup configuration
- Cisco IOS: IOS basic commands
- Cisco IOS: Configure descriptions
- Cisco IOS: Run privileged commands within global config mode
- Cisco IOS: Ports on an IOS device
- Cisco IOS:Pipe character in IOS
- Cisco IOS: IOS boot sequence
- Cisco IOS: Backing up IOS configuration
- IP routing: What is IP routing?
- IP routing: Connected, static & dynamic routes
- IP routing: Administrative distance & metric
- IP routing: Routing protocols
- RIP: RIP overview
- RIP: Configuring RIPv2
- RIP: RIP loop prevention
- EIGRP: EIGRP overview
- EIGRP: EIGRP configuration
- EIGRP: EIGRP automatic & manual summarization
- EIGRP: EIGRP authentication & load balancing
- EIGRP:EIGRP summary
- OSPF: OSPF overview
- OSPF: OSPF configuration
- OSPF: Designated & Backup Designated Router
- OSPF: OSPF authentication
- OSPF: OSPF summarization
- OSPF: OSPF summary
- OSPF: Differences between OSPF and EIGRP
- LAN switching: Layer 2 switching
- LAN switching:Collision & broadcast domain
- LAN switching: CSMA-CD
- VLAN: What is a VLAN?
- VLAN: Configuring VLANs
- VLAN: Configuring access & trunk ports
- VLAN: Frame tagging
- VLAN: IEEE 802.1Q
- VLAN: Inter-Switch Link (ISL)
- ACLs: What are ACLs?
- ACLs: Types of ACLs
- ACLs: Configuring standard ACLs
- ACLs: Configuring extended ACLs
- NAT: What is NAT?
- NAT: Static NAT
- NAT: Dynamic NAT
- IPv6: What is IPv6?
- IPv6: IPv6 address format
- IPv6: Types of IPv6 addresses
- IPv6: IPv6 unicast addresses
- IPv6: IPv6 global unicast addresses
- IPv6: IPv6 unique local addresses
- IPv6: IPv6 link-local addresses
- IPv6: IPv6 multicast addresses
- IPv6: IPv6 address prefixes
- IPv6: IPv6 interface identifier
- IPv6: IPv6 transition options
- IPv6: IPv6 routing protocols
- IPv6: How to configure IPv6
- IPv6: RIPng
- IPv6: Differences between IPv4 and IPv6
- Miscellaneous: Wildcard masks
- Miscellaneous: Setting up Telnet
- Miscellaneous: Setting up SSH
- Miscellaneous: Port security
- Linux Study
- Server Study
- References
- Contact
- Today, there have been 9 visitors (36 hits) on this page!